Hp 530 läppäriin Xp Vistan tilalle!

Eli mun Xp on jo tuo Sp2 päivitetty versio.
Pitänee jostain hankkia tuo SATA-ajuri siis...

HP:llä näyttää olevan myös kaikki WinXP-ajurit tuohon läppäriin.
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=3375995&prodTypeId=321957&prodSeriesId=3375953&swEnvOID=1093&taskId=135&swLang=15

Tuon SATA-ajurin asentamisesta on siellä seuraava ohje:

"1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Execute the downloaded file and follow the on-screen instructions.
A diskette containing the driver is created, and the driver files are
also made available at c:\swsetup\sp36131. If you choose to cancel
diskette creation, you will need to copy the driver files to the
chosen media.

To use the diskette during a new operating system installation, complete the
following steps (choose the procedure that matches the operating system you
are running).

For Microsoft Windows XP:

NOTE: A USB diskette (floppy) drive is required to use this driver. If an
external USB diskette drive is used, ensure that it is plugged into the system
before starting Step 1.

1. Insert the operating system CD, and Power On the notebook to boot
from the CD.

2. At the very beginning of the operating system installation, the following
prompt is displayed at the bottom of the screen:

"Press F6 if you need to install a SCSI or RAID driver...."

When the prompt is displayed, press F6.

3. Later in the operating system installation, you are notified that a mass
storage device could not be detected. When this notification occurs,
press S (S=Specify Additional Device).

4. When prompted, insert the diskette that was created from the SoftPaq file,
and then press Enter.

5. Select "Intel 82801HEM/HBM SATA AHCI Controller (Mobile ICH8M-E/M)" and
press Enter.

NOTE: At this point, the following prompt MAY be displayed, depending on
the version of your operating system CD. If the prompt is displayed, press
Enter to use the default Windows driver and continue, if it is not
displayed, continue with Step 6. The prompt reads as follows:

Windows already has a driver that you can use for
"Intel 82801HEM/HBM SATA AHCI Controller (Mobile ICH8M-E/M)".

Unless the device manufacturer prefers that you use the driver on the
floppy disk, you should use the driver in Windows.

S=use the driver on floppy ENTER=use the default Windows driver

6. Continue with the operating system installation, as prompted.

NOTE: If a problem is encountered when using the external USB floppy drive,
refer to Microsoft Knowledge Base Article 916196: "A connected USB floppy
disk drive does not work when you press F6 to install mass storage drivers
during the Windows XP installation process."
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3375953&swItem=ob-51454-1&prodNameId=3375995&swEnvOID=1093&swLang=15&taskId=135&mode=4&idx=1

Onnea matkaan!

joskus harkinnut kirjoitti:

HP:llä näyttää olevan myös kaikki WinXP-ajurit tuohon läppäriin.
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=3375995&prodTypeId=321957&prodSeriesId=3375953&swEnvOID=1093&taskId=135&swLang=15

Tuon SATA-ajurin asentamisesta on siellä seuraava ohje:

"1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Execute the downloaded file and follow the on-screen instructions.
A diskette containing the driver is created, and the driver files are
also made available at c:\swsetup\sp36131. If you choose to cancel
diskette creation, you will need to copy the driver files to the
chosen media.

To use the diskette during a new operating system installation, complete the
following steps (choose the procedure that matches the operating system you
are running).

For Microsoft Windows XP:

NOTE: A USB diskette (floppy) drive is required to use this driver. If an
external USB diskette drive is used, ensure that it is plugged into the system
before starting Step 1.

1. Insert the operating system CD, and Power On the notebook to boot
from the CD.

2. At the very beginning of the operating system installation, the following
prompt is displayed at the bottom of the screen:

"Press F6 if you need to install a SCSI or RAID driver...."

When the prompt is displayed, press F6.

3. Later in the operating system installation, you are notified that a mass
storage device could not be detected. When this notification occurs,
press S (S=Specify Additional Device).

4. When prompted, insert the diskette that was created from the SoftPaq file,
and then press Enter.

5. Select "Intel 82801HEM/HBM SATA AHCI Controller (Mobile ICH8M-E/M)" and
press Enter.

NOTE: At this point, the following prompt MAY be displayed, depending on
the version of your operating system CD. If the prompt is displayed, press
Enter to use the default Windows driver and continue, if it is not
displayed, continue with Step 6. The prompt reads as follows:

Windows already has a driver that you can use for
"Intel 82801HEM/HBM SATA AHCI Controller (Mobile ICH8M-E/M)".

Unless the device manufacturer prefers that you use the driver on the
floppy disk, you should use the driver in Windows.

S=use the driver on floppy ENTER=use the default Windows driver

6. Continue with the operating system installation, as prompted.

NOTE: If a problem is encountered when using the external USB floppy drive,
refer to Microsoft Knowledge Base Article 916196: "A connected USB floppy
disk drive does not work when you press F6 to install mass storage drivers
during the Windows XP installation process."
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3375953&swItem=ob-51454-1&prodNameId=3375995&swEnvOID=1093&swLang=15&taskId=135&mode=4&idx=1

Onnea matkaan!

Lue lisää

http://www.msfn.org/board/Using-a-F6-Driver-with-USB-Floppy-t82711.html

textsetup.oem tiedostoon kirjoitti:

http://www.msfn.org/board/Using-a-F6-Driver-with-USB-Floppy-t82711.html

Lue lisää

WinXP:n asennus tuohon HP-läppäriin onnistuu googlen mukaan ilman korppuasemaakin.

http://www.google.fi/search?hl=en&safe=off&q="HP 530" sata drivers&btnG=Search&meta=


"Yes, you can install windows xp on hp 530
all what you need to do is to disable some hdd features from the bios:
sata native mode....
bios dma....
data execution....
I really cannot recal the name of features I have disabled since I tried many times
but what you can do for sure is to disable every thing is the "devices settings" (the page that contains option for virtualization at its end) and this will for sure make you able to install and run windows xp
good luck"

"i phoned hp tech support and they said that the sata drive native support in the system configuration section must be disabled. i've tried it and windows is loading."

Kun kiintolevy on löytynyt tuolla kikalla ja käyttis ensin asennettu niin sitten voi jälkeen päin lisätä SATA-ajurit ja sen jälkeen buuttaa bios-asetukset.

korppuasemaa kirjoitti:

WinXP:n asennus tuohon HP-läppäriin onnistuu googlen mukaan ilman korppuasemaakin.

http://www.google.fi/search?hl=en&safe=off&q="HP 530" sata drivers&btnG=Search&meta=


"Yes, you can install windows xp on hp 530
all what you need to do is to disable some hdd features from the bios:
sata native mode....
bios dma....
data execution....
I really cannot recal the name of features I have disabled since I tried many times
but what you can do for sure is to disable every thing is the "devices settings" (the page that contains option for virtualization at its end) and this will for sure make you able to install and run windows xp
good luck"

"i phoned hp tech support and they said that the sata drive native support in the system configuration section must be disabled. i've tried it and windows is loading."

Kun kiintolevy on löytynyt tuolla kikalla ja käyttis ensin asennettu niin sitten voi jälkeen päin lisätä SATA-ajurit ja sen jälkeen buuttaa bios-asetukset.

Lue lisää

"buuttaa" = muuttaa

korjaus korjaus kirjoitti:

"buuttaa" = muuttaa

tuolloin näkyy sata levy käyttöjärjestelmälle pata (ide) levynä ja asennus onnistuu ilman sata-ajureita.

""Native mode" on varmaankin tuo "Oma tila", joka on otettava pois käytöstä"

http://keskustelu.plaza.fi/muropaketti/bbs/t515957

pois päältä kirjoitti:

tuolloin näkyy sata levy käyttöjärjestelmälle pata (ide) levynä ja asennus onnistuu ilman sata-ajureita.

""Native mode" on varmaankin tuo "Oma tila", joka on otettava pois käytöstä"

http://keskustelu.plaza.fi/muropaketti/bbs/t515957

Lue lisää

Mites tuo yllä oleva homma hoituu fuji siemenssin masiinaan ? 3710 Li