Miksi modulit ei lataannu bootissa

kannattas varmaan mainita mitä käyttistä käyttää niin on helpompi neuvoo....

tässä
Nov 21 16:55:44 nauhuri bttv: driver version 0.9.16 loaded
Nov 21 16:55:44 nauhuri bttv: using 8 buffers with 2080k (520 pages) each for capture
Nov 21 16:55:44 nauhuri bttv: Bt8xx card found (0).
Nov 21 16:55:44 nauhuri ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
Nov 21 16:55:44 nauhuri bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 5, latency: 32, mmio: 0xdf102000
Nov 21 16:55:44 nauhuri bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
Nov 21 16:55:44 nauhuri bttv0: using: Hauppauge (bt878) [card=10,insmod option]
Nov 21 16:55:44 nauhuri bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
Nov 21 16:55:44 nauhuri bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
Nov 21 16:55:44 nauhuri tveeprom: Hauppauge: model = 44804, rev = C129, serial# = 3933730
Nov 21 16:55:44 nauhuri tveeprom: tuner = Temic 4006FH5 (idx = 29, type = 14)
Nov 21 16:55:44 nauhuri tveeprom: tuner fmt = PAL(B/G) (eeprom = 0x04, v4l2 = 0x00000007)
Nov 21 16:55:44 nauhuri tveeprom: audio_processor = None (type = 0)
Nov 21 16:55:44 nauhuri bttv0: using tuner=5
Nov 21 16:55:44 nauhuri bttv0: i2c: checking for MSP34xx @ 0x80... not found
Nov 21 16:55:44 nauhuri bttv0: i2c: checking for TDA9875 @ 0xb0... not found
Nov 21 16:55:44 nauhuri bttv0: i2c: checking for TDA7432 @ 0x8a... not found
Nov 21 16:55:44 nauhuri tvaudio: TV audio decoder audio/video mux driver
Nov 21 16:55:44 nauhuri tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 (PV951),ta8874z
Nov 21 16:55:44 nauhuri bttv0: i2c: checking for TDA9887 @ 0x86... not found
Nov 21 16:55:44 nauhuri : chip found @ 0xc2 (bt878 #0 [sw])
Nov 21 16:55:44 nauhuri tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
Nov 21 16:55:44 nauhuri bttv0: registered device video0
Nov 21 16:55:44 nauhuri bttv0: registered device vbi0
Nov 21 16:55:44 nauhuri bttv0: PLL: 28636363 => 35468950 .. ok

.
.
.
Nov 21 16:35:29 nauhuri rc-scripts: Configuration not set for eth0 - assuming dhcp
Nov 21 16:35:29 nauhuri rc-scripts: eth0 does not exist
Nov 21 16:35:33 nauhuri rc-scripts: ERROR: Problem starting needed services.
Nov 21 16:35:33 nauhuri rc-scripts: "mythbackend" was not started.
Nov 21 16:35:33 nauhuri cron[6017]: (CRON) STARTUP (V5.0)
Nov 21 16:35:33 nauhuri rc-scripts: ERROR: Problem starting needed services.

Gentoota en tunne, mutta modulit ladataan hieman jakelusta riippuen:
/etc/modprobe.conf
/etc/modules

Verkkokortin osalta varmaan alias-määrittely /etc/modules.confiin (tai mitä kautta ko. tiedosto sitten luodaakaan) riittänee:
alias eth0 3c59x