Asensin läppäriini 3comin WLAN-kortin ja sille Atmellin ajurin. Koneen käynnistyksessä kone tunnistaa kortin PCMCIA-paikasta.
HArdrake kaipaa kuitenkin jotakin modulia PCMF502r3. Kyseinen moduli löytyi sourgeforgesta.
Miten saan asennettua modulin? Käynnistykseesä kone mainitsee jotain modprobe -r komennosta, joka liittynee jotenkin modulien asentamiseen kerneliin.
Nyt jos yritän käyttää KWIFI manageria tulee ilmoitus että rajapinta ei löydy.
Omat kyvyt loppuivat tähän, joten apu olisi tarpeen.
HArdrake kaipaa kuitenkin jotakin modulia PCMF502r3. Kyseinen moduli löytyi sourgeforgesta.
Miten saan asennettua modulin? Käynnistykseesä kone mainitsee jotain modprobe -r komennosta, joka liittynee jotenkin modulien asentamiseen kerneliin.
Nyt jos yritän käyttää KWIFI manageria tulee ilmoitus että rajapinta ei löydy.
Omat kyvyt loppuivat tähän, joten apu olisi tarpeen.
Vastaukset 5
Vanhimmat
Pohjaan arvailuni pikaiseen hakuun hakusanalla PCMF502r3..
Ilmeisesti se moduli asentui hakemiston /lib/modules/kernelversio/kernel/drivers/pcmcia tai /lib/modules/kernelversio/pcmcia alle ?
Jos löydät noista hakemistoista tiedoston pcmf502r.o, niin testaa (roottina tietysti) komentoa modprobe pcmf502r. Jos modulin laittaminen sisään onnistuu, lsmod tulostaa samannimisen modulin. Jos ei, niin katso mitä dmesg tulostaa.
modproben mukaan modprobe -r poistaa modulin käytöstä.
En ole suorittanut muuta kui n kopioinut imuroimani pcmf502r3.0 modulin hakemistoon, josta kone väitti että sitä ei löydy.Hakemisto oli /lib/modules/kernelversio/pcmcia.
Kopioinnin jälkeenkäynnistyksessä sanotaan että moduli pcmf502r3 is not available.
Modprobe komento ei toiminut. Pitääkö surffata ensi em hakemistoon?
lsmod ei löydä ko. modulia. Kiitos jo etukäteen hyvistä neuvoista joita kaipaan lisää.
dmesg tulostaa.
Linux version 2.6.3-7mdk ([email protected]) (gcc version 3.3.2 (Mandr
ake Linux 10.0 3.3.2-6mdk)) #1 Wed Mar 17 15:56:42 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bef0000 (usable)
BIOS-e820: 000000000bef0000 - 000000000beff000 (ACPI data)
BIOS-e820: 000000000beff000 - 000000000bf00000 (ACPI NVS)
BIOS-e820: 000000000bf00000 - 000000000c000000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
190MB LOWMEM available.
On node 0 totalpages: 48880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 44784 pages, LIFO batch:10
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7450
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0bef8c94
ACPI: FADT (v001 ATI Raptor 0x06040000 ATI 0x000f4240) @ 0x0befee2b
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0befee9f
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x0befeec7
ACPI: DSDT (v001 ATI U1_M1535 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Built 1 zonelists
Kernel command line: BOOT_IMAGE=linux ro root=301 devfs=mount acpi=ht resume=/de
v/hda5 splash=silent
bootsplash: silent mode.
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1789.260 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 189536k/195520k available (1816k kernel code, 5356k reserved, 849k data,
272k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3555.32 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 131k freed
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD mobile AMD Athlon(tm) XP2400+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1788.0717 MHz.
..... host bus clock speed is 264.0995 MHz.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd87b, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router ALI [10b9/1533] at 0000:00:07.0
PCI: IRQ 0 for device 0000:00:0a.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:0a.1
IRQ routing conflict for 0000:00:0a.0, have irq 5, want irq 11
vesafb: framebuffer at 0xe0000000, mapped to 0xcc800000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=67
vesafb: protected mode interface info at c000:51a9
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
apm: BIOS not found.
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x1
Initializing Cryptographic API
ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.4-2004/02/19: looking for picture.... silentjpeg size 14856 bytes
, found (800x600, 14808 bytes, v3).
Console: switching to colour frame buffer device 92x32
pty: 1024 Unix98 ptys configured
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 3 for device 0000:00:08.0
ttyS1 at I/O 0x8828 (irq = 3) is a 8250
ttyS2 at I/O 0x8840 (irq = 3) is a 8250
ttyS3 at I/O 0x8850 (irq = 3) is a 8250
ttyS4 at I/O 0x8860 (irq = 3) is a 8250
ttyS5 at I/O 0x8870 (irq = 3) is a 8250
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Warning: ATI Radeon IGP Northbridge is not yet fully tested.
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK3021GAS, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB), CHS=58140/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
spurious 8259A interrupt: IRQ7.
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 35
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
BIOS EDD facility v0.13 2004-Mar-09, 1 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
Resume Machine: resuming from /dev/hda5
Resuming from device hda5
Resume Machine: This is normal swap space
PM: Reading pmdisk image.
PM: Resume from disk failed.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 272k freed
Real Time Clock Driver v1.12
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Assigned IRQ 9 for device 0000:00:02.0
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: irq 9, pci mem cd92b000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
EXT3 FS on hda1, internal journal
Adding 511520k swap on /dev/hda5. Priority:-1 extents:1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Ati IGP320/M chipset
agpgart: Maximum main memory to use for agp memory: 148M
agpgart: AGP aperture is 64M @ 0xd4000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
ohci1394: $Rev: 1097 $ Ben Collins
PCI: Found IRQ 9 for device 0000:00:0c.0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[d0007000-d00077ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d9d719e5af18b]
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Found IRQ 11 for device 0000:00:12.0
eth0: NatSemi DP8381[56] at 0xcd9d0000, 00:0d:9d:59:c0:32, IRQ 11.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: IRQ 5 for device 0000:00:0a.0 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:0a.0
IRQ routing conflict for 0000:00:0a.0, have irq 5, want irq 11
PCI: Sharing IRQ 11 with 0000:00:0a.1
Yenta: CardBus bridge found at 0000:00:0a.0 [6933:0002]
Yenta: ISA IRQ mask 0x0c98, PCI irq 5
Socket status: 30000810
PCI: Enabling device 0000:00:0a.1 (0080 -> 0082)
PCI: Found IRQ 11 for device 0000:00:0a.1
IRQ routing conflict for 0000:00:0a.0, have irq 5, want irq 11
Yenta: CardBus bridge found at 0000:00:0a.1 [6933:0002]
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x408-0x40f 0x480-0x48f 0
x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
inserting floppy driver for 2.6.3-7mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NET: Registered protocol family 17
eth0: link up.
PCI: Found IRQ 5 for device 0000:00:06.0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
lp0: console ready
mtrr: 0xe0000000,0x4000000 overlaps existing 0xe0000000,0x1000000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes
, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes , v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes , v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes , v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes , v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.4-2004/02/19: looking for picture.... found (800x600, 11943 bytes , v3).
bootsplash: status on console 5 changed to on
SCSI subsystem initialized
st: Version 20040122, fixed bufsize 32768, s/g segs 256
NET: Registered protocol family 10
Disabled Privacy Extensions on device c035fe60(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Katso siltä sivulta mistä saitkin tuon modulin (tai mukana tulleesta ohjeesta) mihin se moduli pitää kopioida. Sen jälkeen sano depmod -a (roottina). Jos homma meni oikein, niin modprobe pcmf502r3 pitäisi toimia, mikä ko. moduli ei vaadi muita moduleita laitettavaksi sitä ennen. Onnistuneessa modprobetuksessa lsmodin pitäisi myös tulostaa ko. modulin nimi. Modprobea käytettäessä ei pidä olla siinä hakemistossa, missä modulikin sijaitsee.
Jos nuo eivät toimi, niin kokeile suoraan insmodilla: "insmod jossainmodulinnimi.o". Virheilmoituksessa katso dmesg-komennon tuloste.
[root@localhost 2.6.3-7mdk]# insmod pcmf502r3.0
insmod: error inserting 'pcmf502r3.0': -1 Invalid module format
Tuosta päätellen ainakin modulissa on jotain vikaa.
Komennon "file pcjotain.o" pitäisi tulostaa jotain tyyliin "ELF 32-bit LSB ..", jos tuo edes on moduli. Onko moduli edes tarkoitettu 2.6:lle ?
Pikaisen haun perusteella (esim. http://lists.jammed.com/linux-security-module/2003/07/0009.html ) syynä voisi olla vanhat moduleohjelmistot, kai sinulla on asennettuna module-init-tools, jota tarvitaan 2.6:lla ?