Haksahdin kokeilmaan pingviiniä ja tuli vastaan langattoman USB adapterin ongelma.Pakkauksesta saadun kuvan perusteella ymmärsin että laitteella olisi Linux yhteensopivuus.Driverit kuitenkin puuttuivat ja sain Jensenscandinavian tuesta driverit mutta en oikein ymmärrä ohjeesta missä hakemistossa pitää olla mitäkin jotta saan ohjaimen asennettua:en löydä mielestäni ohjeen mukaisia hakemistoja enkä myöskään Kernelin soursea,lsusb tunnistaa kuitenkin HW:n:
3. USB interface
3.1 Kernel setup
When you build kernel, choice some option to enable usb support.
(To build kernel, using command "make menuconfig" in text mode or
"make xconfig" in X-window mode, you will need kernel-source to do this)
In config menu, choice the list of options.
USB support->Support for USB
->Preliminary USB device filesystem (Not nacessary)
->UHCI Alternate Driver (JE) support
or
->OHCI (Compaq,iMacs,OPTi,SiS,Ali,...) support
(according your mainboard support)
File systems->/proc file system support(Not nacessary)
**Note : You should choice these options to ensure SiS 016x driver work :
Loadable module support->Enable loadable module support
->Set version information on all module symbols
->Kernel module loader
And then build your kernel.
3.2 USB interface
You can use command 'lsusb' or see /proc/bus/usb/devices to check your
USB device.
Also, /proc/bus/usb/drivers lists all usb driver which is installed in
your kernel.
------------------------------------------------------------------------------
4. Compilation and installation
4.1 Prerequisites and kernel setup
You should need kernel 2.4.0 and later.
You should need kernel source in directory "/usr/src/linux-x.x.x"
4.2 Installation
Using command "./Install" to install SiS 016x driver.
(i) Input kernel source directory path :
(If the default path is wrong, input your currect path and press enter)
Linux kernel source directory [/usr/src/linux-2.4.18-3]:/usr/src/linux-xxx
(ii) Input kernel module directory path :
(If the default path is current, just press enter)
Module install directory [/lib/modules/2.4.18-3]:
(iii) Complete
3. USB interface
3.1 Kernel setup
When you build kernel, choice some option to enable usb support.
(To build kernel, using command "make menuconfig" in text mode or
"make xconfig" in X-window mode, you will need kernel-source to do this)
In config menu, choice the list of options.
USB support->Support for USB
->Preliminary USB device filesystem (Not nacessary)
->UHCI Alternate Driver (JE) support
or
->OHCI (Compaq,iMacs,OPTi,SiS,Ali,...) support
(according your mainboard support)
File systems->/proc file system support(Not nacessary)
**Note : You should choice these options to ensure SiS 016x driver work :
Loadable module support->Enable loadable module support
->Set version information on all module symbols
->Kernel module loader
And then build your kernel.
3.2 USB interface
You can use command 'lsusb' or see /proc/bus/usb/devices to check your
USB device.
Also, /proc/bus/usb/drivers lists all usb driver which is installed in
your kernel.
------------------------------------------------------------------------------
4. Compilation and installation
4.1 Prerequisites and kernel setup
You should need kernel 2.4.0 and later.
You should need kernel source in directory "/usr/src/linux-x.x.x"
4.2 Installation
Using command "./Install" to install SiS 016x driver.
(i) Input kernel source directory path :
(If the default path is wrong, input your currect path and press enter)
Linux kernel source directory [/usr/src/linux-2.4.18-3]:/usr/src/linux-xxx
(ii) Input kernel module directory path :
(If the default path is current, just press enter)
Module install directory [/lib/modules/2.4.18-3]:
(iii) Complete
Vastaukset
Vanhimmat
Ei vielä vastauksia
Aloittaja odottaa vastauksia. Kerro oma näkemyksesi ensimmäisenä.