Minä asensin RH 8:in, mutta siinä ei ole ethernet kortilleni ajureita. Kortin mukana tulleella ajuri disketillä on linuxin ajurit, mutta en tiedä miten ne asennetaan. Tässä copy/pastettu ohjeet englanniksi miten pitäisi toimia... kokeilin noita juttuja mutta komentorivillä ei mikään noista komennoista toiminut...
******* This document contains instructions on Linux driver installation for *******
******* 100/10M Ethernet PCI Adapter *******
The Linux driver for Myson MDT8xx compatible MAC chipset on
this adapter has been embedded into Linux systems since kernel
version 2.4.5, and this makes this adapter automatically detected
and installed with the driver supported by Linux system.
Therefore,
1. If your Linux kernel is still old version 2.2.x, please use
and refer the driver supported for kernel version 2.2.x in
Linux2.2.x directory on the driver diskette.
2. If your Linux kernel is version 2.4.x previous than version
2.4.5, please get the latest kernel file from the web site of The
Linux Kernel Archives (http://www.kernel.org/). Then, install and
re-compile the downloaded latest kernel file into your current
Linux system.
3. If your Linux kernel is or has been patched to version
above 2.4.5 but you have not enabled or configured the MTD8xx
compatible driver as dynamic loadable or embedded system module,
then you could follow the step 4 to enable the driver and
re-compile the kernel.
If you could use the console command "#locate fealnx.o" to
locate the module driver file or find the driver module file
fealnx.o in kernel source /usr/src/linux-2.4.x/drivers/net in
your Linux system, then you could load module into system by
console command "insmod fealnx.o" and then "ifconfig eth0 up" to
bring this adapter to work.
You could use console command "linuxconf" to configure
this adapter card too.
4. If your Linux kernel is any new version above than 2.4.5
(included) and it is a new installation, you can configure the
kernel by following console commands to enable the driver for
100/10M Ethernet PCI Adapter.
#/usr/src/menuconfig
Enable the option of "Myson MTD-8XX PCI Ethernet support"
in "Ethernet (10 or 100 M bit)" of "Network device support" as a
loadable module or system default module.
#make dep
#make clean
#make bzImage
#cp /usr/src/linux-2.4.X/arch/i386/boot/bzImage /boot
Then, edit /etc/lilo.conf, run "/sbin/lilo", and then reboot
your Linux system. After new kernel has been rebooted, it will
automatically load the driver for this adapter.
******* This document contains instructions on Linux driver installation for *******
******* 100/10M Ethernet PCI Adapter *******
The Linux driver for Myson MDT8xx compatible MAC chipset on
this adapter has been embedded into Linux systems since kernel
version 2.4.5, and this makes this adapter automatically detected
and installed with the driver supported by Linux system.
Therefore,
1. If your Linux kernel is still old version 2.2.x, please use
and refer the driver supported for kernel version 2.2.x in
Linux2.2.x directory on the driver diskette.
2. If your Linux kernel is version 2.4.x previous than version
2.4.5, please get the latest kernel file from the web site of The
Linux Kernel Archives (http://www.kernel.org/). Then, install and
re-compile the downloaded latest kernel file into your current
Linux system.
3. If your Linux kernel is or has been patched to version
above 2.4.5 but you have not enabled or configured the MTD8xx
compatible driver as dynamic loadable or embedded system module,
then you could follow the step 4 to enable the driver and
re-compile the kernel.
If you could use the console command "#locate fealnx.o" to
locate the module driver file or find the driver module file
fealnx.o in kernel source /usr/src/linux-2.4.x/drivers/net in
your Linux system, then you could load module into system by
console command "insmod fealnx.o" and then "ifconfig eth0 up" to
bring this adapter to work.
You could use console command "linuxconf" to configure
this adapter card too.
4. If your Linux kernel is any new version above than 2.4.5
(included) and it is a new installation, you can configure the
kernel by following console commands to enable the driver for
100/10M Ethernet PCI Adapter.
#/usr/src/menuconfig
Enable the option of "Myson MTD-8XX PCI Ethernet support"
in "Ethernet (10 or 100 M bit)" of "Network device support" as a
loadable module or system default module.
#make dep
#make clean
#make bzImage
#cp /usr/src/linux-2.4.X/arch/i386/boot/bzImage /boot
Then, edit /etc/lilo.conf, run "/sbin/lilo", and then reboot
your Linux system. After new kernel has been rebooted, it will
automatically load the driver for this adapter.
Vastaukset 5
Vanhimmat
>You could use console command "linuxconf" to
>configure this adapter card too.
-Asenna linuxconf
>#/usr/src/menuconfig
Väärä hakemisto, pitäisi olla /usr/src/kernel-source-x.x.xx
Asensitko kernelin lähdekoodit? Ja sitäpaitsi tuossa hakemistossa pitäisi tehdä make xconfig (tai menuconfig, jos haluaa)
>#make dep
>#make clean
>#make bzImage
>#cp /usr/src/linux-2.4.X/arch/i386/boot/bzImage
>/boot
Ja asensitko kehitystyökalut? Ilman niitä on vähän vaikea ruveta kääntämään kerneliä.
"Väärä hakemisto, pitäisi olla /usr/src/kernel-source-x.x.xx
Asensitko kernelin lähdekoodit? Ja sitäpaitsi tuossa hakemistossa pitäisi tehdä make xconfig (tai menuconfig, jos haluaa)"
"Ja asensitko kehitystyökalut? Ilman niitä on vähän vaikea ruveta kääntämään kerneliä. "
En asentanut lähdekoodia ja kehitystyökaluja. Onko muuta vaihtoehtoa kuin tuo kernelin kääntäminen? Kiitos vastauksesta etukäteen.
> Onko muuta vaihtoehtoa kuin tuo kernelin kääntäminen?
On, jos RedHat on kääntänyt tuon moduuliksi. Mikäs kernel siinä on käynnissä? Saat sen selville käskyllä "uname -r". Jos se on yli 2.4.5, kokeile käskyä "modprobe fealnx". Jos se sanoo ettei tuota moduulia ole, täytyy se kernel käännellä itse.
miten linuxconfilla saa tuon ajurin asennettua... vaihdoin linuxin mandrake 9:iin... siellä laitehallinnassa lukee että ethernet kortti on, mutta ajuria en saa asennettua.. olen kyllä löytänyt sen ajurin, mutta "insmod fealnx.o" antaa jonkin virheilmoituksen....
siis virhe ilmoitus oli tällainen:
"fealnx.o : unresolved symbol_nway_restart_r7a0347d5..."