Accton EN1207D Series PCI Fast Ethernet Adapter v. 1.33.0709.2001 asennusongelma
Miten saan asennettua tuon ajurin, kun siellä ei ole mitään asennustiedostoa.
README.TXT
Lainaus:*******************************************************************
* ACCTON TECHNOLOGY CORPORATION *
* EN1207D/EN2242A Series PCI FAST ETHERNET ADAPTER *
* *
* Copyright (C) 2001 Accton Technology Corporation *
* All Rights Reserved. *
*******************************************************************
How to Config Your PCI adapter
==============================
1. Go to the PCI configuration item in BIOS setup.
2. Follow these steps to configure the PCI slot:
a). You should know which slot your adapter is plugged in to.
Look for the physical location of the slot in your PCI
motherboard.
b). Set the "this device" field to "Enable".
c). Set the "this item" field to "Master".
The EN1207D/EN2242A series PCI adapter MUST be installed in an
expansion slot that supports "Bus Master".
Refer to your system documentation to determine which slots
support Bus Mastering.
d). Some BIOS Setups allow you to select which interrupt line you
can use. In this case, select "INT A" for the "this item" field.
e). Select an IRQ of your choice; make sure it does not conflict
with existing IRQs in use.
d). Select the "Trigger method" by which the IRQ is assigned or
routed to the PCI slot. Choose the "level-trigger" option.
Multiple EN1207D/EN2242A series PCI adapters can share the same PCI
interrupt, but all must use INTA with level-trigger mode.
3. Run the diagnostic program found in the driver diskette under DOS.
If any problem arises during the installation, contact your dealer or
Accton Technology Corporation for support.
Conflict with Microsoft EMM386
==============================
The PCI adapters can only function with the EMM386.EXE memory manager
program version 4.49 or later. You can verify its version number by
entering EMM386 at the DOS Prompt.
Do not specify the "highscan" option with the EMM386.exe statement
in your config.sys file or your system will hang.
If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert
the HIGHSCAN flag into the EMM386 command line. This parameter cannot
be manually removed once it's installed, doing so will cause the
extended memory manager to malfunction.
RELEASE.TXT
Lainaus:*******************************************************************
* ACCTON TECHNOLOGY CORPORATION *
* EN1207D/EN2242A Series PCI FAST ETHERNET ADAPTER *
* SOFTWARE DRIVER RELEASE DISKETTE *
* *
* Copyright (C) 2001 Accton Technology Corporation *
* All Rights Reserved. *
* *
* V1.09D 07-20-2001 *
*******************************************************************
Welcome to Accton's Workgroup Networking family, and
thank you for purchasing one of our many networking products.
If you have any problem about with products, please contact
your dealer or Accton Technology Corporation. (see SUPPORT.TXT)
--------------------------------------------------------------------
Files and
Subdirectories Description
--------------------------------------------------------------------
RELEASE.TXT This file. Presents a summary of the contents
of your Driver Diskette.
README.TXT It includes instructions & troubleshooting guide
for adapter installation.
\SETUP Subdirectory includes user guide for SET1207D.EXE
and the setup program.
\NETWARE Subdirectory for Novell NetWare Drivers
\DOSODI Subdirectory for Novell NetWare DOS/ODI driver
\OS2ODI Subdirectory for Novell NetWare OS2/ODI driver
\SERVER Subdirectory for Novell NetWare Server driver(Spec. 3.31)
\3.1X Subdirectory for Novell 3.1x MSM, NBI modules
\4and5.X Subdirectory for Novell 4.x and 5.x MSM, NBI modules
\LANDRV32 Subdirectory for Novell NetWare Server/ Client 32 driver
(Spec. 3.31)
\WIN95 Subdirectory for NDIS/3 driver for Microsoft
Windows 95 (OSR1) or later on x86 platform.
\WIN95SR2 Subdirectory for NDIS/4 driver for Microsoft
Windows 95 OSR2 or later on x86 platform.
\WIN98 Subdirectory for NDIS/5 driver for Microsoft
Windows 98 and Windows Millennium
\WIN2000 Subdirectory for NDIS/5 driver for Microsoft
Windows 2000 (NT5.0) on x86 platform.
\WINNT Subdirectory for NDIS/4 driver for Windows NT 4.0
on x86 platform.
\NT351 Subdirectory for NDIS/3 driver for Windows NT 3.51
on x86 platform.
\NDIS Subdirectory containing programs and installation
instructions for using the NDIS/2 driver under the
following programs:
* Microsoft Windows for Workgroups
* Microsoft LAN Manager
* IBM LAN Server
* Banyan VINES
* ARTISOFT LANtastic
* Wollongong Pathway Access
* DEC PATHWORKS
* SUN PC-NFS
\MSLANMAN.DOS Subdirectory for DOS NDIS drivers for Microsoft LAN
Manager Versions 1.x and 2.x; the text file for
instructions to install the driver is in the directory
\NDIS. (Lanman.txt)
\MSLANMAN.OS2 Subdirectory for OS2 NDIS drivers for Microsoft LAN
Manager Versions 1.x and 2.x; the text file for
instructions to install the driver is in the directory
\NDIS. (Lanman.txt)
\WFW311 Subdirectory for NDIS/3 driver for Windows for
Workgroups 3.11.
\SCO
\3.X Subdirectory for SCO Unix 3.2.4 driver.
\5.X Subdirectory for SCO Unix 5.0 driver.
\PKTDRV Subdirectory for FTP spec-compliant packet driver;
also includes instructions on installing the driver
\SUPPORT Subdirectory includes information for Accton's
Technical Support.
--------------------------------------------------------------------
*** All trademarks or brand names mentioned are trademarks or
registered trademarks of their respective companies.
RECORD OF REVISIONS FOR DRIVER RELEASES
=======================================
----------------------------------------------------------------
Release Number/ Changes
Date
----------------------------------------------------------------
V1.00 . New Release
02/25/1998
V1.01
05/28/1998 . Moddified for cable length of 100M (EN5030)
V1.02
07/15/1998 . Moddified for Nways Function
. Enabled Bus Master
V1.03
12/23/1998 . Added NDIS/5 Driver
. Added OS2/ODI Driver
. Added Power Management function in Setup Program
. Modified NDIS 3/4 Driver (Tx Threshold) Performace
. Modified DOSODI Driver Performace
V1.04 Beta1
02/08/1999 . Add Win95 NDIS/2,ODI Driver Support.
. Modify NDIS/2 DOS ,NDIS/3 Driver for Support
RPL BOOTROM boot Win95
V1.04
05/10/1999 . Modify NDIS/2 Driver for WIN95 Support.
. Add support unattended install for Win NT4.0
. Add Cat file for supporting Interagated 10/100 Fast
Ethernet Driver
V1.05 Beta1 . Modify NDIS4 driver for the override INF file
V1.05 Beta2 . Update NDIS 3/4/5 driver
. Update OEMSETUP.INF file in \WINNT directory
. Update SCO Unix 5 driver to get higher media
compatibility.
V1.05 . Separate the NDIS 3/4 driver for Win95 and
10/22/1999 OSR2
. Add PC99 certified CAT file for Win98/2000
V1.06 Beta1 . Update NDIS5 driver to solve some error
02/16/2000 handling problems.
V1.06 . Update the NDIS5 driver to pass the HCT9.5
03/10/2000
V1.07 . Update SET1207D.EXE
04/10/2000 . Add Netware 5.x driver installation guide
V1.08a
04/25/2000 . add a parameter "Wakeup Frame" to disable
the Pattern-Match function in NDIS5 driver
V1.08b
05/08/2000 . support EN2242A series Adapter
V1.08c . Updated NDIS3/4/5 driver to fix improper wakeup
08/31/2000 behaviour due to applying wrong checksum mechanism
in 5038B chip.
. Fix "driver-update" problem in OEMSETUP.INF for
WINNT
. Add WinME and Win2000 WHQL CAT files in \WIN98
and \WIN2000
V1.08d . Update NDIS3/4 driver to disable the MS wakeup
09/22/2000 frame feature in driver.
. Put Win98 and WinME drivers in different
directory due to they use different CAT files.
. Update WFW311 OEMSETUP.INF file to save
disk space.
V1.09B . Update NDIS5 Driver for support Smart Power Saving
05/22/2001 . Add receive Buffer to 64K
. Fix link led problem in Windows 2000
V1.09D . Add New ID For NDID5/NDIS4/NDIS3 INF files
07/20/2001
-----------------------------------------------------------------
--- End of File ---
Miten saan asennettua tuon ajurin, kun siellä ei ole mitään asennustiedostoa.
README.TXT
Lainaus:*******************************************************************
* ACCTON TECHNOLOGY CORPORATION *
* EN1207D/EN2242A Series PCI FAST ETHERNET ADAPTER *
* *
* Copyright (C) 2001 Accton Technology Corporation *
* All Rights Reserved. *
*******************************************************************
How to Config Your PCI adapter
==============================
1. Go to the PCI configuration item in BIOS setup.
2. Follow these steps to configure the PCI slot:
a). You should know which slot your adapter is plugged in to.
Look for the physical location of the slot in your PCI
motherboard.
b). Set the "this device" field to "Enable".
c). Set the "this item" field to "Master".
The EN1207D/EN2242A series PCI adapter MUST be installed in an
expansion slot that supports "Bus Master".
Refer to your system documentation to determine which slots
support Bus Mastering.
d). Some BIOS Setups allow you to select which interrupt line you
can use. In this case, select "INT A" for the "this item" field.
e). Select an IRQ of your choice; make sure it does not conflict
with existing IRQs in use.
d). Select the "Trigger method" by which the IRQ is assigned or
routed to the PCI slot. Choose the "level-trigger" option.
Multiple EN1207D/EN2242A series PCI adapters can share the same PCI
interrupt, but all must use INTA with level-trigger mode.
3. Run the diagnostic program found in the driver diskette under DOS.
If any problem arises during the installation, contact your dealer or
Accton Technology Corporation for support.
Conflict with Microsoft EMM386
==============================
The PCI adapters can only function with the EMM386.EXE memory manager
program version 4.49 or later. You can verify its version number by
entering EMM386 at the DOS Prompt.
Do not specify the "highscan" option with the EMM386.exe statement
in your config.sys file or your system will hang.
If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert
the HIGHSCAN flag into the EMM386 command line. This parameter cannot
be manually removed once it's installed, doing so will cause the
extended memory manager to malfunction.
RELEASE.TXT
Lainaus:*******************************************************************
* ACCTON TECHNOLOGY CORPORATION *
* EN1207D/EN2242A Series PCI FAST ETHERNET ADAPTER *
* SOFTWARE DRIVER RELEASE DISKETTE *
* *
* Copyright (C) 2001 Accton Technology Corporation *
* All Rights Reserved. *
* *
* V1.09D 07-20-2001 *
*******************************************************************
Welcome to Accton's Workgroup Networking family, and
thank you for purchasing one of our many networking products.
If you have any problem about with products, please contact
your dealer or Accton Technology Corporation. (see SUPPORT.TXT)
--------------------------------------------------------------------
Files and
Subdirectories Description
--------------------------------------------------------------------
RELEASE.TXT This file. Presents a summary of the contents
of your Driver Diskette.
README.TXT It includes instructions & troubleshooting guide
for adapter installation.
\SETUP Subdirectory includes user guide for SET1207D.EXE
and the setup program.
\NETWARE Subdirectory for Novell NetWare Drivers
\DOSODI Subdirectory for Novell NetWare DOS/ODI driver
\OS2ODI Subdirectory for Novell NetWare OS2/ODI driver
\SERVER Subdirectory for Novell NetWare Server driver(Spec. 3.31)
\3.1X Subdirectory for Novell 3.1x MSM, NBI modules
\4and5.X Subdirectory for Novell 4.x and 5.x MSM, NBI modules
\LANDRV32 Subdirectory for Novell NetWare Server/ Client 32 driver
(Spec. 3.31)
\WIN95 Subdirectory for NDIS/3 driver for Microsoft
Windows 95 (OSR1) or later on x86 platform.
\WIN95SR2 Subdirectory for NDIS/4 driver for Microsoft
Windows 95 OSR2 or later on x86 platform.
\WIN98 Subdirectory for NDIS/5 driver for Microsoft
Windows 98 and Windows Millennium
\WIN2000 Subdirectory for NDIS/5 driver for Microsoft
Windows 2000 (NT5.0) on x86 platform.
\WINNT Subdirectory for NDIS/4 driver for Windows NT 4.0
on x86 platform.
\NT351 Subdirectory for NDIS/3 driver for Windows NT 3.51
on x86 platform.
\NDIS Subdirectory containing programs and installation
instructions for using the NDIS/2 driver under the
following programs:
* Microsoft Windows for Workgroups
* Microsoft LAN Manager
* IBM LAN Server
* Banyan VINES
* ARTISOFT LANtastic
* Wollongong Pathway Access
* DEC PATHWORKS
* SUN PC-NFS
\MSLANMAN.DOS Subdirectory for DOS NDIS drivers for Microsoft LAN
Manager Versions 1.x and 2.x; the text file for
instructions to install the driver is in the directory
\NDIS. (Lanman.txt)
\MSLANMAN.OS2 Subdirectory for OS2 NDIS drivers for Microsoft LAN
Manager Versions 1.x and 2.x; the text file for
instructions to install the driver is in the directory
\NDIS. (Lanman.txt)
\WFW311 Subdirectory for NDIS/3 driver for Windows for
Workgroups 3.11.
\SCO
\3.X Subdirectory for SCO Unix 3.2.4 driver.
\5.X Subdirectory for SCO Unix 5.0 driver.
\PKTDRV Subdirectory for FTP spec-compliant packet driver;
also includes instructions on installing the driver
\SUPPORT Subdirectory includes information for Accton's
Technical Support.
--------------------------------------------------------------------
*** All trademarks or brand names mentioned are trademarks or
registered trademarks of their respective companies.
RECORD OF REVISIONS FOR DRIVER RELEASES
=======================================
----------------------------------------------------------------
Release Number/ Changes
Date
----------------------------------------------------------------
V1.00 . New Release
02/25/1998
V1.01
05/28/1998 . Moddified for cable length of 100M (EN5030)
V1.02
07/15/1998 . Moddified for Nways Function
. Enabled Bus Master
V1.03
12/23/1998 . Added NDIS/5 Driver
. Added OS2/ODI Driver
. Added Power Management function in Setup Program
. Modified NDIS 3/4 Driver (Tx Threshold) Performace
. Modified DOSODI Driver Performace
V1.04 Beta1
02/08/1999 . Add Win95 NDIS/2,ODI Driver Support.
. Modify NDIS/2 DOS ,NDIS/3 Driver for Support
RPL BOOTROM boot Win95
V1.04
05/10/1999 . Modify NDIS/2 Driver for WIN95 Support.
. Add support unattended install for Win NT4.0
. Add Cat file for supporting Interagated 10/100 Fast
Ethernet Driver
V1.05 Beta1 . Modify NDIS4 driver for the override INF file
V1.05 Beta2 . Update NDIS 3/4/5 driver
. Update OEMSETUP.INF file in \WINNT directory
. Update SCO Unix 5 driver to get higher media
compatibility.
V1.05 . Separate the NDIS 3/4 driver for Win95 and
10/22/1999 OSR2
. Add PC99 certified CAT file for Win98/2000
V1.06 Beta1 . Update NDIS5 driver to solve some error
02/16/2000 handling problems.
V1.06 . Update the NDIS5 driver to pass the HCT9.5
03/10/2000
V1.07 . Update SET1207D.EXE
04/10/2000 . Add Netware 5.x driver installation guide
V1.08a
04/25/2000 . add a parameter "Wakeup Frame" to disable
the Pattern-Match function in NDIS5 driver
V1.08b
05/08/2000 . support EN2242A series Adapter
V1.08c . Updated NDIS3/4/5 driver to fix improper wakeup
08/31/2000 behaviour due to applying wrong checksum mechanism
in 5038B chip.
. Fix "driver-update" problem in OEMSETUP.INF for
WINNT
. Add WinME and Win2000 WHQL CAT files in \WIN98
and \WIN2000
V1.08d . Update NDIS3/4 driver to disable the MS wakeup
09/22/2000 frame feature in driver.
. Put Win98 and WinME drivers in different
directory due to they use different CAT files.
. Update WFW311 OEMSETUP.INF file to save
disk space.
V1.09B . Update NDIS5 Driver for support Smart Power Saving
05/22/2001 . Add receive Buffer to 64K
. Fix link led problem in Windows 2000
V1.09D . Add New ID For NDID5/NDIS4/NDIS3 INF files
07/20/2001
-----------------------------------------------------------------
--- End of File ---
Vastaukset 9
Vanhimmat
os haluatte ladata koneelle tuon päivityksen ja tarkastella sen sisältöä, niin ladatkaa täältä:
http://rapidshare.com/files/11096101/EN1207DTXv133.zip
-Hiiren oikealla Oma tietokone
-Hallitse
-Laitehallinta
-Verkkosovittimista hiiren oikealla oikean verkkokortin päällä
-Päivitä ohjain
-Update sivustoa kysyttäessä -Ei tällä kertaa
-Asenna luettelosta tai määritellystä sijainnista
-Älä etsi valitsen ohjaimen itse
-Levy, selaa, avaa ohjaimen asennustiedosto, missä sijaitseekin, mahdollisesti c:n juuressa, tai minne olet sen purkanut ja etsit sieltä .inf tiedoston
-Avaa, ok, valmis
Toimiiko se noin, koska verkkokorttina minulla on Realtek RTL8139 Family PCI Fast Ethernet NIC ja toi Accton EN1207D Series PCI Fast Ethernet Adapter on joku lisäjuttu.
Toihan on verkkokortti.
Onko sitten kaksi verkkokorttia koneessa?
Sitä mä en tiiä, mut DriverAgent.comissa sanottiin että pitäis Realtekin kortti päivittää tolla, ja näköjään tällä hetkelläkin siitä on vanhempi versio koneella. Realtekin kortti on sen omalla päivitykselä päivitetty ja Windows ei tota kortti Laitehallinnassa näytä, mutta ilmeisesti se on tässä koneessa.
DriverAgentista:
Driver Agent Scan Results
4% of your drivers are old
Good Good Drivers (96%)
Bad Bad Drivers (4%)
Bad Driver
Network adapters
Realtek RTL8139 Family PCI Fast Ethernet NIC
Joku toinen saa jatkaa tästä, menee kyllä minun ymmärryksen yli jos kehoitetaan eri verkkokortin ajureita asentelemaan..
En asentaisi, ennemmin hakisin Realtekillä mahdolliset uudemmat ajurit.
Realtekin uusimmat ajurit on, mutta koneella on myös tuo acctonin höskä johon kannattaisi ajurit asentaa, koska DriverAgent valittaa, että liian vanhat ajurit. Acctonin juttu on koneella kerta koneella oli jo valmiiksi sen vanhempi versio.
se on Realtekin klooni, sellaisen käsityksen sain kun hieman googletin.
No mutta en osaa auttaa, enkä ainakaan uskalla neuvoa Realtekin verkkokortille asentamaan noita ajureita.
Jospa joku asiasta enemmän tietävä tulisi neuvomaan kunhan nämä sivut taas alkavat joskus toimimaan.
Windows-verkko on Realtekin ja PCI- tai PnP-verkko on Acctonin. Ohessa kuvat:
Realtek:
http://i112.photobucket.com/albums/n191/Memb_2006/Realtek.jpg
Accton:
http://i112.photobucket.com/albums/n191/Memb_2006/Accton.jpg
http://i112.photobucket.com/albums/n191/Memb_2006/Accton2.jpg
http://i112.photobucket.com/albums/n191/Memb_2006/Accton3.jpg
Ja vielä kuva laitehallinnasta, jossa ei Acctonia näy: http://i112.photobucket.com/albums/n191/Memb_2006/Laitehallinta.jpg
Ongelmanahan oli se, että miten asennan tuon Acctonin ajurin.