Ubuntu-koneesta lämmöt näkyviin

Kaikista avoimen koodin sovelluksisista löytyi Xsensors, jonka asensin, ja se paneeliin.
Työpöydälle ilmestyy vain pikkuruisia pystysuorakaiteita, joista vetämällä aukeaa tyhjä ruutu.
Sitten asensin tuolta Omnibookin, kun on HP:n läppäri, ja tulee ilmoitus, että ajuri jo on:
http://sensors-applet.sourceforge.net/
eikä tapahdu mitään...

Törmättiinkö tässä taas näytönohjaimeen?

sensors-applet ja lm-sensors on asennettu.
Missäs muodossa sensors-detect annetaan ja päätteeseenkö se laitetaan?
You need to be root- sanoo hän.

/// kirjoitti:

sensors-applet ja lm-sensors on asennettu.
Missäs muodossa sensors-detect annetaan ja päätteeseenkö se laitetaan?
You need to be root- sanoo hän.

sensors-detect ajetaan komentoriviltä komennolla

sudo sensors-detect

ja kaikkiin muihin voit vastata oletuksen mukaisen "yes" mutta jossain ihan lopussa kysytään kirjoitetaanko tiedostoon /etc/modules niin siihen joudut kirjoittamaan "yes". Sitten on sensors-applet käytettävissä paneelissa.

/// kirjoitti:

sensors-applet ja lm-sensors on asennettu.
Missäs muodossa sensors-detect annetaan ja päätteeseenkö se laitetaan?
You need to be root- sanoo hän.

sudo sensors-detect

exergy kirjoitti:

sensors-detect ajetaan komentoriviltä komennolla

sudo sensors-detect

ja kaikkiin muihin voit vastata oletuksen mukaisen "yes" mutta jossain ihan lopussa kysytään kirjoitetaanko tiedostoon /etc/modules niin siihen joudut kirjoittamaan "yes". Sitten on sensors-applet käytettävissä paneelissa.

Lue lisää

Koko kaavan ajoin, ja vastasi:

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported.

exergy kirjoitti:

sensors-detect ajetaan komentoriviltä komennolla

sudo sensors-detect

ja kaikkiin muihin voit vastata oletuksen mukaisen "yes" mutta jossain ihan lopussa kysytään kirjoitetaanko tiedostoon /etc/modules niin siihen joudut kirjoittamaan "yes". Sitten on sensors-applet käytettävissä paneelissa.

Lue lisää

hannu@hannu-laptop:~$ sudo sensors-detect
# sensors-detect revision 5249 (2008-05-11 22:56:25 0200)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Sorry, no supported PCI bus adapters found.

If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown chip with ID 0x0f00
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown non-standard chip with ID 0x7a

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See
http://www.lm-sensors.org/wiki/FAQ/Chapter3 for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.

/// kirjoitti:

hannu@hannu-laptop:~$ sudo sensors-detect
# sensors-detect revision 5249 (2008-05-11 22:56:25 0200)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Sorry, no supported PCI bus adapters found.

If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown chip with ID 0x0f00
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown non-standard chip with ID 0x7a

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See
http://www.lm-sensors.org/wiki/FAQ/Chapter3 for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.

Lue lisää

Eli se ei vaan löytänyt mitään antureita, mikähän emo tuo mahtaa olla? Minullakin on pari emoa joilta linux ei löydä antureita vaikka ne varmasti ovat olemassa. Onko siinä antureita? Biosista näkee ellei muualta, sielät jostain saattaa löytyä "hardware probing" tms. kohta josta näet lämpötilat. Ellei sellasita kohtaa ole niin ehkä emolla ei ole mitään antureita, jos on niin ovat jotain erikoisempia joita linux ei tunnista.

/// kirjoitti:

hannu@hannu-laptop:~$ sudo sensors-detect
# sensors-detect revision 5249 (2008-05-11 22:56:25 0200)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Sorry, no supported PCI bus adapters found.

If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown chip with ID 0x0f00
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown non-standard chip with ID 0x7a

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See
http://www.lm-sensors.org/wiki/FAQ/Chapter3 for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.

Lue lisää

pelkällä sensors-komennolla:

hannu@hannu-laptop:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: 47.0°C (crit = 105.0°C)
temp2: 46.0°C (crit = 103.0°C)
temp3: 16.0°C (crit = 105.0°C)
temp4: 40.0°C (crit = 110.0°C)


Toimivaa sovellusta kuitenkaan ei ole
Siivous on kaukana.

/// kirjoitti:

pelkällä sensors-komennolla:

hannu@hannu-laptop:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: 47.0°C (crit = 105.0°C)
temp2: 46.0°C (crit = 103.0°C)
temp3: 16.0°C (crit = 105.0°C)
temp4: 40.0°C (crit = 110.0°C)


Toimivaa sovellusta kuitenkaan ei ole
Siivous on kaukana.

Lue lisää

No oletko nyt kokeillut lisätä anturi-apletin paneeliin? Eikö sellaista ole valikoimassa?

exergy kirjoitti:

No oletko nyt kokeillut lisätä anturi-apletin paneeliin? Eikö sellaista ole valikoimassa?

Kun kyse on softa-valvonnasta on siihen muutenkin aina syytä suhtautua varauksella, arvojahan voi korjata miten huvittaa joten ei ole mitään takeita että ohjelmallinen anturi näyttää oikein ellei laita rauta-anturia rinnalle ja "kalibroi" softa-anturia. Tämän siis huomaa eri koneissa hyvin kun eri käyttöjärjestelmissä softa-anturit näyttävät ihan mitä sattuu..

exergy kirjoitti:

No oletko nyt kokeillut lisätä anturi-apletin paneeliin? Eikö sellaista ole valikoimassa?

Näiden värkkäämisten jälkeen sinne "Lisää paneeliin"-valikoimaan onkin ilmestynyt Laitteistoantureiden valvonta.
Onnistui tämä sittenkin.

Kiitoksia vastanneille.