Miten asennan Matrox ajurit Gentoon? (Matrox G200)
Joku mga.o pitäisi jostain löytää?
Joku mga.o pitäisi jostain löytää?
Matrox ajurit
xorg
18867
0Äänestä
Muut lukivat myös
Odottaa vastausta
Näihin keskusteluihin ei ole vielä vastattu. Ole ensimmäinen.
Vastaukset 18
Vanhimmat
Oletko valinnut kerneliin Matrox:in ajurin?
Device Drivers --->
Character devices --->
[*] Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)
< > 3dfx Banshee/Voodoo3
< > 3dlabs GMX 2000
< > ATI Rage 128
< > ATI Radeon
< > Intel I810 (NEW)
< > Intel 830M, 845G, 852GM, 855GM, 865G (NEW)
< > Intel 830M, 845G, 852GM, 855GM, 865G, 915G (NEW)
Matrox g200/g400
< > SiS video cards
Mutta kiinteästi kernelissä, ei moduulina, ja jostain syystä xorg ei löytänyt sitä. Käänsin moduuliksi ja nyt se löytää sen, mutta tulee tuollainen:
(EE) MGA(0): [drm] DRIScreenInit failed. Disabling DRI.
Onko logitiedostossa /var/log/Xorg.0.log muita virheilmoituksia, mitä dmesg ilmoittaa näytönohjaimesta?
(--) MGA(0): Chipset: "mgag200"
(==) MGA(0): Depth 16, (==) framebuffer bpp 16
(==) MGA(0): RGB weight 565
(==) MGA(0): Using AGP 1x mode
(--) MGA(0): Linear framebuffer at 0xE5000000
(--) MGA(0): MMIO registers at 0xEFEFC000
(--) MGA(0): Pseudo-DMA transfer window at 0xEF000000
(--) MGA(0): BIOS at 0xEFEE0000
(II) Truncating PCI BIOS Length to 32768
(--) MGA(0): Video BIOS info block at offset 0x07AC0
(--) MGA(0): Found and verified enhanced Video BIOS info block
(II) MGA(0): MGABios.RamdacType = 0x0
(**) MGA(0): VideoRAM: 8192 kByte
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
(==) MGA(0): Write-combining range (0xe5000000,0x800000)
(II) MGA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) MGA(0): I2C bus "DDC P1" initialized.
(II) MGA(0): I2C device "DDC P1:ddc2" registered at address 0xA0.
(II) MGA(0): I2C device "DDC P1:ddc2" removed.
(II) MGA(0): I2C Monitor info: (nil)
(II) MGA(0): end of I2C Monitor info
(--) MGA(0): No DDC signal
(II) MGA(0): DDC Monitor info: (nil)
(II) MGA(0): end of DDC Monitor info
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.1.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) MGA(0): initializing int10
(II) MGA(0): Primary V_BIOS segment is: 0xc000
(II) MGA(0): VESA BIOS detected
(II) MGA(0): VESA VBE Version 2.0
(II) MGA(0): VESA VBE Total Mem: 8192 kB
(II) MGA(0): VESA VBE OEM: Matrox Graphics Inc.
(II) MGA(0): VESA VBE OEM Software Rev: 2.6
(II) MGA(0): VESA VBE OEM Vendor: Matrox
(II) MGA(0): VESA VBE OEM Product: MGA-G200
(II) MGA(0): VESA VBE OEM Product Rev: 00
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) MGA(0): VESA VBE DDC supported
(II) MGA(0): VESA VBE DDC Level none
(II) MGA(0): VESA VBE DDC transfer in appr. 0 sec.
(II) MGA(0): VESA VBE DDC read failed
(==) MGA(0): Using gamma correction (1.0, 1.0, 1.0)
(==) MGA(0): Min pixel clock is 12 MHz
(==) MGA(0): Max pixel clock is 250 MHz
(II) MGA(0): Monitor0: Using hsync range of 30.00-71.00 kHz
(II) MGA(0): Monitor0: Using vrefresh range of 50.00-120.00 Hz
(II) MGA(0): Clock range: 12.00 to 250.00 MHz
(II) MGA(0): Not using default mode "1280x960" (hsync out of range)
(II) MGA(0): Not using default mode "640x480" (hsync out of range)
(II) MGA(0): Not using default mode "1280x1024" (hsync out of range)
(II) MGA(0): Not using default mode "640x512" (hsync out of range)
(II) MGA(0): Not using default mode "1280x1024" (hsync out of range)
(II) MGA(0): Not using default mode "640x512" (hsync out of range)
(II) MGA(0): Not using default mode "1600x1200" (hsync out of range)
(II) MGA(0): Not using default mode "800x600" (hsync out of range)
(II) MGA(0): Not using default mode "1600x1200" (hsync out of range)
(II) MGA(0): Not using default mode "800x600" (hsync out of range)
(II) MGA(0): Not using default mode "1600x1200" (hsync out of range)
(II) MGA(0): Not using default mode "800x600" (hsync out of range)
(II) MGA(0): Not using default mode "1600x1200" (hsync out of range)
(II) MGA(0): Not using default mode "800x600" (hsync out of range)
(II) MGA(0): Not using default mode "1600x1200" (hsync out of range)
(II) MGA(0): Not using default mode "800x600" (hsync out of range)
(II) MGA(0): Not using default mode "1792x1344" (hsync out of range)
(II) MGA(0): Not using default mode "896x672" (hsync out of range)
(II) MGA(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "896x672" (hsync out of range)
(II) MGA(0): Not using default mode "1856x1392" (hsync out of range)
(II) MGA(0): Not using default mode "928x696" (hsync out of range)
(II) MGA(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "928x696" (hsync out of range)
(II) MGA(0): Not using default mode "1920x1440" (hsync out of range)
(II) MGA(0): Not using default mode "960x720" (hsync out of range)
(II) MGA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "960x720" (hsync out of range)
(II) MGA(0): Not using default mode "1400x1050" (hsync out of range)
(II) MGA(0): Not using default mode "700x525" (hsync out of range)
(II) MGA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "960x720" (hsync out of range)
(II) MGA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "1024x768" (hsync out of range)
(II) MGA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "1024x768" (hsync out of range)
(II) MGA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) MGA(0): Not using default mode "1024x768" (hsync out of range)
(II) MGA(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) MGA(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) MGA(0): Not using default mode "1280x960" (width too large for virtual size)
(II) MGA(0): Not using default mode "1152x864" (width too large for virtual size)
(II) MGA(0): Not using default mode "1152x768" (width too large for virtual size)
(--) MGA(0): Virtual size is 1024x768 (pitch 1024)
(**) MGA(0): *Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) MGA(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 hsync vsync
(**) MGA(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) MGA(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 hsync vsync
(**) MGA(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) MGA(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) MGA(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz
(II) MGA(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 hsync vsync
(**) MGA(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz
(II) MGA(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
(**) MGA(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
(II) MGA(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
(**) MGA(0): Default mode "1024x768": 44.9 MHz, 35.5 kHz, 87.1 Hz (I)
(II) MGA(0): Modeline "1024x768" 44.90 1024 1032 1208 1264 768 768 776 817 interlace hsync vsync
(**) MGA(0): Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz
(II) MGA(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync
(**) MGA(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) MGA(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 hsync vsync
(**) MGA(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) MGA(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 hsync vsync
(**) MGA(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) MGA(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 hsync vsync
(**) MGA(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) MGA(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 hsync vsync
(**) MGA(0): Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D)
(II) MGA(0): Modeline "700x525" 61.00 700 744 820 940 525 526 532 541 doublescan hsync vsync
(**) MGA(0): Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D)
(II) MGA(0): Modeline "640x512" 54.00 640 664 720 844 512 512 514 533 doublescan hsync vsync
(**) MGA(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) MGA(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) MGA(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) MGA(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync
(**) MGA(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) MGA(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(**) MGA(0): Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D)
(II) MGA(0): Modeline "640x480" 54.00 640 688 744 900 480 480 482 500 doublescan hsync vsync
(**) MGA(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz
(II) MGA(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync vsync
(**) MGA(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) MGA(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync vsync
(**) MGA(0): Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D)
(II) MGA(0): Modeline "576x432" 54.00 576 608 672 800 432 432 434 450 doublescan hsync vsync
(**) MGA(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) MGA(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 hsync -vsync
(**) MGA(0): Default mode "576x384": 32.5 MHz, 44.2 kHz, 54.8 Hz (D)
(II) MGA(0): Modeline "576x384" 32.50 576 589 657 736 384 385 388 403 doublescan hsync vsync
(**) MGA(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D)
(II) MGA(0): Modeline "512x384" 47.25 512 536 584 688 384 384 386 404 doublescan hsync vsync
(**) MGA(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D)
(II) MGA(0): Modeline "512x384" 39.40 512 520 568 656 384 384 386 400 doublescan hsync vsync
(**) MGA(0): Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D)
(II) MGA(0): Modeline "512x384" 37.50 512 524 592 664 384 385 388 403 doublescan -hsync -vsync
(**) MGA(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D)
(II) MGA(0): Modeline "512x384" 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync
(**) MGA(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 87.1 Hz (D)
(II) MGA(0): Modeline "512x384" 22.45 512 516 604 632 384 384 388 409 interlace doublescan hsync vsync
(**) MGA(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D)
(II) MGA(0): Modeline "416x312" 28.64 416 432 464 576 312 312 314 333 doublescan -hsync -vsync
(**) MGA(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D)
(II) MGA(0): Modeline "400x300" 28.15 400 416 448 524 300 300 302 315 doublescan hsync vsync
(**) MGA(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(II) MGA(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 doublescan hsync vsync
(**) MGA(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D)
(II) MGA(0): Modeline "400x300" 25.00 400 428 488 520 300 318 321 333 doublescan hsync vsync
(**) MGA(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(II) MGA(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 doublescan hsync vsync
(**) MGA(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
(II) MGA(0): Modeline "400x300" 18.00 400 412 448 512 300 300 301 312 doublescan hsync vsync
(**) MGA(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D)
(II) MGA(0): Modeline "320x240" 18.00 320 348 376 416 240 240 242 254 doublescan -hsync -vsync
(**) MGA(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D)
(II) MGA(0): Modeline "320x240" 15.75 320 328 360 420 240 240 242 250 doublescan -hsync -vsync
(**) MGA(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D)
(II) MGA(0): Modeline "320x240" 15.75 320 332 352 416 240 244 245 260 doublescan -hsync -vsync
(**) MGA(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(II) MGA(0): Modeline "320x240" 12.60 320 328 376 400 240 245 246 262 doublescan -hsync -vsync
(**) MGA(0): Default mode "360x200": 17.8 MHz, 37.9 kHz, 85.0 Hz (D)
(II) MGA(0): Modeline "360x200" 17.75 360 378 414 468 200 200 202 223 doublescan -hsync vsync
(**) MGA(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) MGA(0): Modeline "320x200" 15.75 320 336 368 416 200 200 202 222 doublescan -hsync vsync
(**) MGA(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) MGA(0): Modeline "320x175" 15.75 320 336 368 416 175 191 192 222 doublescan hsync -vsync
(==) MGA(0): DPI set to (75, 75)
(II) MGA(0): YDstOrg is set to 0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xef000000 - 0xef7fffff (0x800000) MX[B]
[1] 0 0 0xefefc000 - 0xefefffff (0x4000) MX[B]
[2] 0 0 0xe5000000 - 0xe5ffffff (0x1000000) MX[B]
[3] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[4] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xeffee000 - 0xeffeefff (0x1000) MX[B]
[9] -1 0 0xeedff000 - 0xeedfefff (0x0) MX[B]O
[10] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[B]O
[11] -1 0 0xefee0000 - 0xefeeffff (0x10000) MX[B](B)
[12] -1 0 0xef000000 - 0xef7fffff (0x800000) MX[B](B)
[13] -1 0 0xefefc000 - 0xefefffff (0x4000) MX[B](B)
[14] -1 0 0xe5000000 - 0xe5ffffff (0x1000000) MX[B](B)
[15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[19] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[20] -1 0 0x0000de00 - 0x0000de3f (0x40) IX[B]
[21] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[22] -1 0 0x0000dc00 - 0x0000dbff (0x0) IX[B]O
[23] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[24] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(==) MGA(0): Write-combining range (0xe5000000,0x800000)
(II) MGA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) MGA(0): 64 DWORD fifo
(==) MGA(0): Default visual is TrueColor
(II) MGA(0): [drm] bpp: 16 depth: 16
(II) MGA(0): [drm] Sarea 2200 664: 2864
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: Searching for BusID pci:0000:01:05.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
(II) MGA(0): [drm] drmOpen failed
(EE) MGA(0): [drm] DRIScreenInit failed. Disabling DRI.
(II) MGA(0): Using 3327 lines for offscreen memory.
(II) MGA(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid filled trapezoids
8x8 mono pattern filled rectangles
8x8 mono pattern filled trapezoids
Indirect CPU to Screen color expansion
Screen to Screen color expansion
Solid Lines
Dashed Lines
Scanline Image Writes
Offscreen Pixmaps
Driver provided FillMono8x8PatternRects replacement
Setting up tile and stipple cache:
32 128x128 slots
18 256x256 slots
6 512x512 slots
(==) MGA(0): Backing store disabled
(==) MGA(0): Silken mouse enabled
(**) Option "dpms"
(**) MGA(0): DPMS enabled
(II) MGA(0): Using overlay video
(==) MGA(0): Direct rendering disabled
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
EndSection
Section "Module"
Load "record"
Load "extmod"
Load "dbe"
Load "dri"
Load "glx"
Load "xtrap"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbLayout" "fi"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Buttons" "5"
Option "ZAxisMapping" "4 5"
EndSection
Section "Device"
Identifier "Card0"
Driver "mga"
VideoRam 8192
VendorName "Matrox Graphics, Inc."
BoardName "MGA G200 AGP"
BusID "PCI:1:5:0"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "SNY"
ModelName "CPD-100ES"
HorizSync 30.0-71.0
VertRefresh 50.0-120.0
Option "DPMS"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Tämä on ehkä tyhmä kysymys, mutta latautuuko mga-moduuli käynnistyksessä.
modprobe mga
startx
>modprobe mga
>startx
Samat virheilmoitukset kuin ennen.
Muistaakseni myös agpgart-moduli piti olla käännetty mukaan. Se taitaa löytyä jostain character devicesin alta, jos kääntelet itse oman kernelisi.
Ensin kannattaa tietysti kokeilla onko se käännetty jo moduliksi komennolla modprobe agpgart.
Kiinteästi kernelissä:
/dev/agpgart (AGP Support)
"Miten asennan Matrox ajurit Gentoon? (Matrox G200)"
Matrox-ajurit löytyvät Atin sivuilta. Samoin myös _ohjeet_ niiden asentamiseksi.
Kaikissa jakeluissa on valittavissa vaihtoehtoiset, vapaat ajurit, jotka toimivat ihan ok.
Hieman jää epäilyttämään, onko todellakaan Gentoo juuri Sinulle sopiva jakelu.
> Matrox-ajurit löytyvät Atin sivuilta. Samoin myös _ohjeet_ niiden asentamiseksi.
Oletko aivan varma tuosta? Kuulostaa aika hassulta jos näin on. En ainakaan itse siltä mitään löytänyt.
http://www.matrox.com/mga/support/drivers/latest/home.cfm
Jeps. näin on...
Mutta, jos ei alkuperäinen kyselijä selviä oman näyttökorttinsa kanssa... olisi varmasti hyvä valita jakelu, jolla omalle näytönohjaimelle löytyy tuki jo jakelusta - ilman kernelin kääntöjä.
Joku ??
Sopivalla hakusanalla google sylkäisi sivun:
http://display-and-video.free-driver-download.com/Matrox/752/Matrox-G200-G400-G400-G400MAX-G450-Display-Driver--1.3.0-For-Linux.html
Mutta toki kannattaa tarkistaa joitakin muitakin linkkejä.
Mutta eiköhän jo jokaisessa Linux-jakelussa ole tuolle kortille käypä ajuri. Hyvin yleinen kortti myös Linux-käytössä.
Laitatko vielä, mitä dmesg näyttää.
Esitä kysymys Gentoon forumilla, siellä on osaavia kavereita neuvomassa.
http://forums.gentoo.org/viewforum-f-47.html
$ dmesg
Linux version 2.6.11-gentoo-r11 (root@gentoo) (gcc version 3.3.5-20050130 (Gentoo 3.3.5.20050130-r1, ssp-3.3.5.20050130-1, pie-8.7.7.1)) #5 SMP Thu Jun 30 21:26:10 EEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000027ff0000 (usable)
BIOS-e820: 0000000027ff0000 - 0000000027ff8000 (ACPI data)
BIOS-e820: 0000000027ff8000 - 0000000028000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB LOWMEM available.
On node 0 totalpages: 163824
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 159728 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fabc0
ACPI: RSDT (v001 AMIINT 0x00000010 MSFT 0x00000097) @ 0x27ff0000
ACPI: FADT (v001 AMIINT 0x00000010 MSFT 0x00000097) @ 0x27ff0030
ACPI: DSDT (v001 AMD75X IRONGATE 0x00001000 MSFT 0x0100000b) @ 0x00000000
Allocating PCI resources starting at 28000000 (gap: 28000000:d7ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 video=matroxfb:1024x768@85
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01545000)
Initializing CPU#0
CPU 0 irqstacks, hard=c051b000 soft=c0513000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 757.676 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 644088k/655296k available (2836k kernel code, 10700k reserved, 1084k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1490.94 BogoMIPS (lpj=745472)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c3f9ff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 1c00)
CPU0: AMD Athlon(tm) Processor stepping 01
per-CPU timeslice cutoff: 1462.34 usecs.
task migration cache decay timeout: 2 msecs.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 01
groups: 01
domain 1: span 01
groups: 01
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI-1138: *** Error: Method execution failed [\MCTH] (Node e7fee580), AE_AML_BUFFER_LIMIT
ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node e7feef40), AE_AML_BUFFER_LIMIT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1120463069.260:0): initialized
inotify device minor=63
Installing knfsd (copyright (C) 1996 [email protected]).
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 11 (level, low) -> IRQ 11
matroxfb: Matrox Millennium G200 (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 1024x768x8bpp (virtual: 1024x8192)
matroxfb: framebuffer at 0xE5000000, mapped to 0xe8880000, size 8388608
Console: switching to colour frame buffer device 128x48
fb0: MATROX frame buffer device
vesafb: Matrox, MGA-G200, 00 (OEM: Matrox Graphics Inc.)
vesafb: VBE version: 2.0
vesafb: protected mode interface info at c000:7b00
vesafb: pmi: set display start = c00c7b92, set palette = c00c7bfe
vesafb: pmi: ports = 3de 3df
vesafb: monitor limits: vf = 0 Hz, hf = 0 kHz, clk = 0 MHz
vesafb: scrolling: redraw
vesafb: cannot reserve video memory at 0xe5000000
vesafb: framebuffer at 0xe5000000, mapped to 0xe9900000, using 600k, total 8192k
fb1: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
ACPI: Thermal Zone [THRM] (30 C)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0c.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xde00. Vers LK1.1.19
eth0: Dropping NETIF_F_SG since no checksum feature.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD7409: IDE controller at PCI slot 0000:00:07.1
AMD7409: chipset revision 7
AMD7409: not 100% native mode: will probe irqs later
AMD7409: 0000:00:07.1 (rev 07) UDMA66 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Uniform CD-ROM driver Revision: 3.20
libata version 1.10 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI interrupt 0000:00:07.4[D] -> GSI 12 (level, low) -> IRQ 12
ohci_hcd 0000:00:07.4: Advanced Micro Devices [AMD] AMD-756 [Viper] USB
ohci_hcd 0000:00:07.4: irq 12, pci mem 0xeffee000
ohci_hcd 0000:00:07.4: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:07.4: AMD756 erratum 4 workaround
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.2
usb 1-1: new full speed USB device using ohci_hcd and address 2
usb 1-2: new low speed USB device using ohci_hcd and address 3
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x000E
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse? Explorer] on usb-0000:00:07.4-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
ip_conntrack version 2.1 (5119 buckets, 40952 max) - 220 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 UAR1 USB
ACPI: (supports S0 S1 S4 S5)
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1
ReiserFS: hdd1: Using r5 hash to sort names
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
"Esitä kysymys Gentoon forumilla"
No, hyvä neuvo, mutta miksi merta edemmä...
Newssit ovat hyvä kyselypaikka.
Matrox on monella käytössä, joten luulisi ongelman ratkeavan.